Find us on Facebook

Made from Organic Flax Seeds. 100% Chemical Free. The Way Paint Used to Be! An "acrylic-free" website.

(585) 924-8070

  Zero Waste Paint
  Ottosson Linseed Oil Paint
  Allback Linseed Oil Paint
  Viking Linseed Oil Paint
  Linseed Oil Stain
  Falun Red Exterior Paint
  Zinc White
  Interior/Exterior Primer
  Luslack Spackle
  Purified Linseed Oil
  Linseed Oil Putty
  Linseed Oil Soap
  Linseed Oil Wax
  Linseed Oil Varnish
  Pine Tar
  Fireplace Paint
  Vehicle Rust Proofing
  Paint Brushes
  Tools & Accessories
  Case Studies
  Product Information
  Speak to the Painter
  Customer Service

Other Products You Can Feel Good About:

  The Silent Paint Remover™
  Paint Brushes & Rollers
  Organic Cleaning Products
  HEPA Vacuum Cleaners
  Solid Teak Windows

Linseed Oil Putty

Video Clip: Linseed Glazing - 3,097KB (QuickTime Player required.)

Linseed Glazing Instructions: English | Spanish

Click to Enlarge Image Below

Linseed Glazing Putty  Linseed oil glazing is made form Purified Organic Raw Linseed Oil. From Allback.


4.4 lb. Tub # 50019
Price: $28.50


3 Pack of Tubs (each 4.4 lb.) # 50380
Price: $79.50

  View Larger Image

DANA Putty Dana putty is also a traditional basic linseed oil putty made in Sweden. Easy glazing putty to work with and a filler for small cracks. Make sure to paint over same day with the Linseed Oil Paint. A preferred glazing putty by most contractors and painters in Sweden. Knead to a soft compound. Avoid acrylic paint on linseed oil putty.

If the putty has dried out completely you can also use our Organic Raw Linseed Oil for maintenance.



11 lb. Tub # 68305
Price: $49.50

2-Pack (11 lb. Tubs) # 68305-2
Price: $39.50 Each

Get $20.00 off when purchasing two 11 lb. tubs.

12.7 oz Tub (375 ml.)
Price: $9.50


View Larger Image




Linseed Oil Glazing Putty Linseed oil glazing putty in a Tube 1.5 LB. Fits standard gun. For glazing window panes and filling cracks. Must be painted over with linseed oil paint. Maintained with purified raw linseed oil over time as the surface start looking dry or faded. Watch window restoration video for information.


1.5 lb. Tube # AFFAP
Price: $11.95


Linseed Oil Spackle INTERIOR ONLY. Spackle that can be sanded. Let dry, sand to a smooth surface and paint over with linseed oil paint. Apply on any clean and dry surface.


1.05 Qt. # P1500
Price: $33.50


Pumice Powder Pumice powder for window restoration. 2 lb bag. For use when you apply the linseed oil glazing compound onto the window and you want to remove any excess linseed oil from the glass. The pumice powder has a great ability to soak up the oil. Pumice powder works significantly better than regular chalk when it comes to absorbing oil. Brush a small amount of pumice powder on the glass with a natural brush.


2 lb. # 50609
Price: $14.95

  View Larger Image

Paint Immediately: You may paint with Linseed Oil Paint right after the Linseed Oil Putty is applied. This is an amazing time saver. The linseed glazing may be used for filling cracks as well.

Instructions for Use: Remove putty from the container and cut/break into four pieces. Heat, two pieces at a time, for ten seconds test carefully. You may heat the putty for a further ten seconds in five-second intervals, if necessary. Knead the putty until smooth on a cold surface. The microwave will dry the putty slightly; this can be remedied by adding a teaspoon of our raw linseed oil when kneading the product.

Cracked front putty can be temporarily sealed by adding a few drops of turpentine to some fresh putty and applying this with a brush over the top of the cracks. Dry off with paper after about fifteen minutes. Can then be painted immediately.

Consistency of Linseed Oil Glazing Putty: Consistency of Linseed Oil Glazing Putty: It is very easy to knead the oil into the glazing after you have heated the glazing in a microwave oven for 10 to 15 seconds. Heat with 5 second increments. Remove the heated glazing from the container onto a cold surface. Knead the oil into the glazing until it has a doughy consistency. A soft glazing is required when you are going to apply Linseed Oil Putty behind the glass (back bed ) in a sash, (setting the glass into a bed of Linseed Oil Putty). The Linseed Oil Putty also needs to be relatively soft to better adhere to wood or glass. A dry Linseed Oil Putty will crack and subsequently fail within a short time. You can use small amounts of chalk (whiting) to soak up any linseed oil that might have gotten on the glass after applying all the glazing needed. You do not usually have to add any chalk (whiting) to the Linseed Oil Putty itself.

Note: Make sure you apply shellac onto the glazing grooves before you apply any glazing. The applied shellac in the glazing grooves will prevent the oil in the glazing from drying out. This will make the Linseed Oil Putty last for a very long time. Shellac flakes work the best. Mix the shellac flakes with just a few drops of denatured alcohol. The mixture should be of the consistency of syrup. With thick shellac you will only need one coat. Shellac is an excellent barrier. Drying time is one hour. Maintain the paint and the Linseed Oil Putty with the Allback Purified Organic Boiled Linseed Oil or the Linseed Oil Wax.


Home  |  About Viking Sales  |  Zero Waste Paint  |  Linseed Oil Paint  |  Interior Primer |  Falun Red Paint  |  Purified Linseed Oil  |  Linseed Oil Putty  |  Linseed Oil Soap  |  Linseed Oil Wax  |  Linseed Oil Varnish  |  Pine Tar  |  Paint Brushes  |  Tools & Accessories  |  Case Studies  |  Product Information  |  FAQ  |  Speak to the Painter  |  Workshops  |  Update Shopping Cart  | Check Out

Web Site design by Alexa Castle